tan (max.) aluminum electrolytic capacitors chip type acoustic series within the wide temperature range. applicable to automatic mounting machine fed with carrier tape. compliant to the rohs directive (2011/65/eu) specifications category temperature range rated voltage range rated capacitance range capacitance tolerance leakage current tangent of loss angle (tan ) stability at low temperature endurance shelf life resistance to soldering heat marking performance characteristics item 40 to +105? 6.3 to 50v 0.1 to 1000 f 20% (120hz, 20?) after 1 minute's application of rated voltage, leakage current is not more than 0.03 cv or 4 ( a) , whichever is greater. black print on the case top. measurement frequency : 120hz at 20? capacitance change leakage current the specifications listed at right shall be met when the capacitors are restored to 20 ? after the rated voltage is applied for 1000 hours at 105 ?. after storing the capacitors under no load at 105? for 1000 hours and then performing voltage treatment based on jis c 5101-4 clause 4.1 at 20?, they shall meet the specified values for the endurance characteristics listed above. tan within 20% of the initial capacitance value 200% or less than the initial specified value less than or equal to the initial specified value rated voltage (v) 6.3 0.30 10 0.26 16 0.22 25 0.16 35 0.13 50 0.12 measurement frequency : 120hz z 25? / z+20? z 40? / z+20? rated voltage (v) impedance ratio zt / z20 (max.) 6.3 4 8 10 3 5 16 2 4 25 2 3 35 2 3 50 2 3 capacitance change leakage current tan within 10% of the initial capacitance value less than or equal to the initial specified value less than or equal to the initial specified value u 1 u 2 q 3 0 4 j 5 1 6 0 7 1 8 m 9 c 10 l 11 1 12 g 13 b 14 configuration taping code size code capacitance tolerance ( 20%) rated voltage (6.3v ) rated capacitance (100 f) series name type d 4 to 6.3 8~10 code gb gs voltage (j:6.3v) capacitance series lot no. a2 100 j uq plastic platform 0.3max. l 0.1 0.2 d0.5 a0.2 a0.2 b 0.2 c0.2 0.5max. e h positive negative (mm) a b c e l h 4 5.4 1.8 4.3 4.3 1.0 5.4 0.5 to 0.8 5 5.4 2.1 5.3 5.3 1.3 5.4 0.5 to 0.8 6.3 5.4 2.4 6.6 6.6 2.2 5.4 0.5 to 0.8 8 6.2 3.3 8.3 8.3 2.3 6.2 0.5 to 0.8 8 10 2.9 8.3 8.3 3.1 10 0.8 to 1.1 10 10 3.2 10.3 10.3 4.5 10 0.8 to 1.1 d l plastic platform 0.3max. l 0.3 d0.5 a0.2 a0.2 b 0.2 c0.2 0.5max. e h positive negative lot no. capacitance series trade mark voltage (a : 10v) a2 100a uq plastic platform 0.3max. l 0.5 d0.5 a0.2 a0.2 b 0.2 c0.2 0.5max. e h positive negative lot no. capacitance series trade mark voltage (v : 35v) a2 100v uq chip type type numbering system (example : 6.3v 100 f) the capacitors are kept on a hot plate for 30 seconds, which is maintained at 250 c. the capacitors shall meet the characteristic requirements listed at right when they are removed from the plate and restored to 20 c. uq series chip type, for audio equipment wide temperature range uq chip type mw dimension table in next page. ( 4 to 6.3) ( 8 6.2l) ( 8 10l, 10 10l) rated voltage v 6.3 10 16 25 35 50 code j a c e v h cat.8100c
0.1 0.22 0.33 0.47 1 2.2 3.3 4.7 10 22 33 47 100 220 330 470 1000 0r1 r22 r33 r47 010 2r2 3r3 4r7 100 220 330 470 101 221 331 471 102 4 5.4 5 5.4 5 5.4 6.3 5.4 8 6.2 8 6.2 8 10 10 10 22 30 36 60 102 (210) 102 (210) 210 (310) 310 4 5.4 5 5.4 5 5.4 6.3 5.4 6.3 5.4 8 6.2 8 10 8 10 22 27 35 46 60 (90) 102 (210) 210 (310) 210 (310) 4 5.4 5 5.4 6.3 5.4 6.3 5.4 8 6.2 8 10 8 10 8 10 18 30 40 50 102 (210) 210 (310) 210 (310) 210 (310) 4 5.4 5 5.4 6.3 5.4 6.3 5.4 8 6.2 8 10 10 10 13 23 38 48 66 155 300 4 5.4 5 5.4 6.3 5.4 8 6.2 8 10 10 10 10 10 15 25 42 59 155 300 300 4 5.4 4 5.4 4 5.4 4 5.4 4 5.4 4 5.4 4 5.4 5 5.4 6.3 5.4 8 6.2 8 10 8 10 10 10 1.0 2.6 3.2 3.8 6.2 11 14 19 30 51 140 180 220 rated ripple current (marms) at 105 c 120hz 0j 6.3 1a 10 1c 16 1e 25 1v 35 1h 50 dimensions rated ripple case size d l (mm) code cap.(f) v frequency coefficient of rated ripple current coefficient frequency 50 hz 120 hz 300 hz 1 khz 10 khz or more 0.70 1.00 1.17 1.36 1.50 taping specifications are given in page 23. recommended land size, soldering by reflow are given in page 18, 19. please refer to page 3 for the minimum order quantity. aluminum electrolytic capacitors uq series size 8 6.2l is available for capacitors marked. " " size 8 10l is available for capacitors marked. " " size 10 10l is available for capacitors marked. " " in this case, 6 will be put at 12th digit of type numbering system. cat.8100c
|
